Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
The writer is making a number of great points about How to Install a Bathtub as a whole in the article on the next paragraphs.
Setting up a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is also a moderately challenging project. If the old tub is readily easily accessible, the job can relocate immediately; if you need to open up a wall surface to remove the old bathtub and also place the new bathtub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to move out the old tub and set in the brand-new one. See to it you have actually certified yourself for the task and fit trying it. As opposed to employing a professional to take over a halfway-completed task, it is much better to consider using one before you start. Opportunities are you may require an expert plumber to make tube connections.
This article will certainly assist you install a brand-new bathtub in your washroom if you have actually already bought a brand-new bathtub and do not require to alter the arrangement of your previous water pipelines.
Your tools and product list ought to consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be rather bothersome due to the limited gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers are in location in between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous type must be attached to the tap ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using the two wooden boards under its feet, place the bathtub in the called for position. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and changing the feet on the tub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Activate the water system as well as inspect all joints and new pipework for leakages and also tighten them if needed. Fill up the bathtub and additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and also securing around the bathtub should wait up until the tub has been made use of at the very least once as this will certainly resolve it into its last placement.
Getting ready for the Setup
To start with, the supporting frame provided with the bath should be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its final setting.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall between the bathroom and the tiling, causing complications with moisture as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and installations. They are marketed in tubes as well as cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealant can break rather early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been guided to that write-up about How to Install a Bathtub Yourself through an associate on a different website. Are you aware of anybody else who is occupied with the subject? Do not hesitate to share it. I recognize the value of reading our article about How to Install a Bathtub.
Suggested Site Report this page